View previous topic :: View next topic |
Author |
Message |
U2U2U2
Joined: 06 Jul 2001 Posts: 5467 Location: Shipsterns Bluff, Tasmania. Colorado
|
Posted: Tue Oct 22, 2019 10:33 am Post subject: |
|
|
FWIW,
When home in Colorado, I take the screws out, after sailing. My next location may be higher than the 6000 feet elevation I’m at. One of my favorite spots , 11,111, and to get there I go over passes that are 12,000, this is feet above sea level.
When I go to California, Hood River or OuterBanks I leave the screws in while there, removing on departure. _________________ K4 fins
4Boards....May the fours be with you
http://www.k4fins.com/fins.html
http://4boards.co.uk/ |
|
Back to top |
|
|
isobars
Joined: 12 Dec 1999 Posts: 20936
|
Posted: Tue Oct 22, 2019 10:43 am Post subject: |
|
|
boardsurfr wrote: | The other board had a top delam from heavy use (~150 sessions) and (again) very light construction. The foam was crushed over a wide area. |
I'll bet that could have been prevented or greatly delayed by adding deck pads. Add traction, comfort, reduced joint trauma, zero chance of forgetting them once installed, and in some cases cosmetics, and ya got a win/win/win/win/win/win scenario. I buy the material with 3M self-stick backing from NSI in Hood River by the full sheet in many colors and have put them on scores of boards with great results in all six win columns. |
|
Back to top |
|
|
cgoudie1
Joined: 10 Apr 2006 Posts: 2599 Location: Killer Sturgeon Cove
|
Posted: Tue Oct 22, 2019 11:44 am Post subject: |
|
|
Hey Gary,
I'd forget my head is it wasn't attached ;*) Pants are pretty obvious, but I'm
sure I've forgotten them on occasion, and heck yeh, when I've been on
meds (I'm not right now) I definitely forget them.
I leave all my boards with fin in, another less thing to occupy my mind when
heading for the water.
Ever forgotten your harness until you try and hook in?
-Craig
U2U2U2 wrote: | Forgetting to install the vent screw is interesting, do you remember to install pants when you wake up?
Take your medications / vitamins? File your tax return ETC ETC etc
Fin ? |
|
|
Back to top |
|
|
swchandler
Joined: 08 Nov 1993 Posts: 10588
|
Posted: Tue Oct 22, 2019 12:39 pm Post subject: |
|
|
"Ever forgotten your harness until you try and hook in?"
I've done that, but more often I put on my seat harness but forget to tighten the webbing on the spreader bar. Another embarrassing classic is forgetting to remove the fin cover after installing the fin.
Regarding deck delaminations between the front and rear footstraps, I learned from Mike Zajicek back in the 90s that ESP foam density is quite variable from spec. I have a couple of his boards that eventually got soft in that area after many years of use. It's not surprising that they were the lightest of the many boards that he made for me. And, anyone who is familiar with Zajicek's boards knows he's not one to build a questionable product.
Mike also shared with me a simple test to learn how fresh your board is over time. Take a quarter on edge between your fingers and repeatedly tap the bottom of the board in areas under the footstraps, and then compare with different areas, particularly in the front 1/3 of the board. If the board is tired and reaching the end of its life, the sound in the tail area will lack the crispiness and resonance you will find forward on the board. You have to remember that the bottom of your board takes one hell of beating over time given your weight and the impact over rough water. Add lots of jumps into the mix, and I think you can get the picture. |
|
Back to top |
|
|
boardsurfr
Joined: 23 Aug 2001 Posts: 1266
|
Posted: Tue Oct 22, 2019 1:36 pm Post subject: |
|
|
isobars wrote: | boardsurfr wrote: | The other board had a top delam from heavy use (~150 sessions) and (again) very light construction. The foam was crushed over a wide area. |
I'll bet that could have been prevented or greatly delayed by adding deck pads. |
Very unlikely, considering that the first signs of softness were under the front footpads.
I checked with a repair place about fixing it but he did not want to touch it. His advice was to keep sailing it until it broke completely.I did that, and the softness spread slowly. Eventually I did a repair, mostly to see how it's done. Proper reconstruction (dig out, rebuild, sandwich, glass) worked, PU plugs not so much - the softness spread to the back of the board, requiring a second repair. I can see why the experienced repair guy did not want to touch it! |
|
Back to top |
|
|
boardsurfr
Joined: 23 Aug 2001 Posts: 1266
|
Posted: Tue Oct 22, 2019 1:42 pm Post subject: |
|
|
swchandler wrote: |
Mike also shared with me a simple test to learn how fresh your board is over time. Take a quarter on edge between your fingers and repeatedly tap the bottom of the board in areas under the footstraps, and then compare with different areas, particularly in the front 1/3 of the board. If the board is tired and reaching the end of its life, the sound in the tail area will lack the crispiness and resonance you will find forward on the board. You have to remember that the bottom of your board takes one hell of beating over time given your weight and the impact over rough water. Add lots of jumps into the mix, and I think you can get the picture. |
Nice test. When I recently install foil tracks in a team edition freestyle board, I was quite surprised to find a double sandwich layer at the bottom under the rear straps. I don't know how far forward it extended. There also was a double sandwich near the fin, with a small region of just a single sandwich in between. The double sandwich looked like it was close to indestructible, even the router complained a bit |
|
Back to top |
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum You can attach files in this forum You can download files in this forum
|
|
|